CAM HINGE H15 PARTS Mold


  CAM VADR H15 PARTS


Mold Type: This is a 8x8" manual mold.
Temperature: 200C at zone 1
Material: Glass Filled PP Black
Additional Plates: None
Cavities: 1
Cycle Time: 60 seconds
Expected Output: 60 parts per hour, 50 with beaks (maybe less)

Notes:

  • Please read JY350-ST power on/off procedure first here.

  • Please read the JY-350-ST 8x8 automatic mold installation guide here.

This part is the side parts of CAM Hinge used on shelters. It is the H15 version. This mold is part of a set. The other parts for this product are in CAM VADR HINGE MAIN Mold.

Operation

This mold is fairly automatic and should eject easily. It might require a little help by pushing up on the front right cornet of the insert as it ejecting. This Mold has no inserts.

Quality Checks

  1. Make sure the part is fully formed.
  2. Check that the part is flat and not warped.
  3. Remove any flashing or gate remains.

Machine Setup:

This data is correct as of 2026/08/18. The mold shot with just a little flash and ejected properly.

PORCHESON   Mold Open/Close Set
MovMould 15.4 mm
Act Pres Flux Place
CLOF 90.0 0.0 150.0 mm
LOWP 60.0 0.0 40.4 mm
HIGP 45.00 0.0 2.50 s
Act Pres Flux Place
0. LOW 50.0 0.0 130.0 mm
0. FS 80.0 0.0 50.0 mm
0. SL 60.0 0.0 6.0 mm
Unloa 50.0 0.0 25.00 s
Slow Set
M.C.Pres 30.0 bar
M.C.Flux 0.0 %
M.O.Pres 20.0 bar
M.O.Flux 0.0 %
Low. P.T 30.00 S
LMT C/O T 30.00 S
Mach Hand Disable
Ejec. InMdCl 0.00


PORCHESON   INJ Set
Screw P: 54.95 mm
Act Pres Flux position
Inj1 50.0 0.0 65.00
Inj2 50.0 0.0 20.00
Inj3 20.0 0.0 15.00
Inj4 0.0 0.0 90.00
Inj5 0.0 0.0 0.00
Hold.Pr 50.0 0.0 8.00 S
Hold.Pr 0.0 0.0 0.00 S
Hold.Pr 0.0 0.0 0.00 S
INJ.T 5.00 S
INJ.Mode Location
Loct.Mode *****
InjCheck Disable
PmtError± 0.00 mm
InjCheckPos 0.00 mm


PORCHESON   Melt/Auto CI StuffSet
Screw P: 67.42 mm
Act Pres PrePress Flux Position
B. Tk 60.0
0.0 80.00
Melt3 100.0 60.0 0.0 77.00
Melt2 0.0 50.0 0.0 10.00
Melt1 0.0 20.0 0.0 0.00
F. Tk 0.0
0.0 0.00
MeltLmt 60.00 S
FirstCool 0.00 S
ThenCool 0.00 S
CoolStopM Disable
CI. StuffS Pres Flux Time
TaKe 70.0 0.0 1.00
Melt 80.0 0.0 1.00
Inje 80.0 0.0 5.00
Cl. Stuff Enable
Cl. Times 999


PORCHESON   NOZZ/EJECT SET
Act Pres Flux Time Place
NozzUp 10.0 0.0 1.00 ******
NozDown 5.0 0.0 1.00 ******
L. Keep 20.0 0.0 1.00 ******
L. EjcAdv 40.0 0.0 3.00 ******
L. EjcRet 5.0 0.0 1.00 ******
R. Keep 0.0 0.0 1.00 ******
R. EjcAdv 5.0 0.0 1.00 ******
R. EjcRet 5.0 0.0 1.00 ******
L. EjectPlac ****** mm
R. EjectPlac ****** mm

AutoNozRet Disable

EjectFunc Enable
EjectMode Times
Ejec. Times 1
EjecAdvDel 3.00 S
EjecRetDel 0.00 S


PORCHESON   Temp. Set

TempCurve Ejec 1Seg 2Seg 3Seg
Meas (°C) ***** % <temp> <temp> <temp>
Set (°C) ***** 215.0 215.0 215.0
Max (+) *** 75.0 75.0 75.0
Min (-) *** 75.0 75.0 75.0
Station **** Lower Lower Lower
Eje. Mode O.ring Scr. C. BT. T 2.00 S Galv
KeepWarm Disable Insulation valu *** °C

NOTES/HISTORY

  • 2026-07-18 - Updated tables. The mold shot with just a very little flash and ejected properly.
  • 2026-07-18 - Created page to capture information