Communion Cup Mold
|
Communion Cup Mold |
Mold Type: This is a 8x8" manual mold.
Temperature: 200C at zone 1
Material: Natural FDA PP with White Dye
Additional Plates: None
Cavities: 8
Cycle Time: 60 seconds
Expected Output: 480 parts per hour, 400 with beaks
Notes:
- Please read JY350-ST power on/off procedure first here.
-
Please read the JY-350-ST 8x8 automatic mold installation guide here.
This part is communion cup with a little bread side and a deeper part for the juice or wine.
Operation
This mold is fairly automatic and should eject the 8 communion cups after each shot.
Quality Checks
- Make sure the part is fully formed.
- Check that the part is flat and not warped.
- Remove any flashing or gate remains.
Machine Setup:
This data is correct as of 2026/07/28. The mold shot with just a little flash and ejected properly.
PORCHESON Mold Open/Close Set
MovMould 15.4 mm
| Act | Pres | Flux | Place |
|---|---|---|---|
| CLOF | 80.0 | 0.0 | 150.0 mm |
| LOWP | 80.0 | 0.0 | 32.8 mm |
| HIGP | 120.00 | 0.0 | 1.00 s |
| Act | Pres | Flux | Place |
|---|---|---|---|
| 0. LOW | 30.0 | 0.0 | 130.0 mm |
| 0. FS | 30.0 | 0.0 | 50.0 mm |
| 0. SL | 10.0 | 0.0 | 6.0 mm |
| Unloa | 25.0 | 0.0 | 3.00 s |
| Slow Set | |
|---|---|
| M.C.Pres | 30.0 bar |
| M.C.Flux | 0.0 % |
| M.O.Pres | 20.0 bar |
| M.O.Flux | 0.0 % |
| Low. P.T | 30.00 S |
| LMT C/O T | 30.00 S |
| Mach Hand | Disable |
| Ejec. InMdCl | 0.00 |
PORCHESON INJ Set
Screw P: 54.95 mm
| Act | Pres | Flux | position |
|---|---|---|---|
| Inj1 | 100.0 | 0.0 | 100.00 |
| Inj2 | 90.0 | 0.0 | 90.00 |
| Inj3 | 80.0 | 0.0 | 90.00 |
| Inj4 | 80.0 | 0.0 | 90.00 |
| Inj5 | 0.0 | 0.0 | 0.00 |
| Hold.Pr | 40.0 | 0.0 | 0.00 S |
| Hold.Pr | 0.0 | 0.0 | 0.00 S |
| Hold.Pr | 0.0 | 0.0 | 0.00 S |
| INJ.T | 6.00 S |
| INJ.Mode | Location |
| Loct.Mode | ***** |
| InjCheck | Disable |
| PmtError± | 0.00 mm |
| InjCheckPos | 0.00 mm |
PORCHESON Melt/Auto CI StuffSet
Screw P: 67.42 mm
| Act | Pres | PrePress | Flux | Position |
|---|---|---|---|---|
| B. Tk | 80.0 | 0.0 | 86.00 | |
| Melt3 | 120.0 | 60.0 | 0.0 | 86.00 |
| Melt2 | 100.0 | 50.0 | 0.0 | 10.00 |
| Melt1 | 50.0 | 20.0 | 0.0 | 0.00 |
| F. Tk | 0.0 | 0.0 | 0.00 |
| MeltLmt | 60.00 S |
| FirstCool | 0.00 S |
| ThenCool | 0.00 S |
| CoolStopM | Disable |
| CI. StuffS | Pres | Flux | Time | |
|---|---|---|---|---|
| TaKe | 70.0 | 0.0 | 1.00 | |
| Melt | 80.0 | 0.0 | 1.00 | |
| Inje | 80.0 | 0.0 | 5.00 |
| Cl. Stuff | Enable |
| Cl. Times | 999 |
PORCHESON NOZZ/EJECT SET
| Act | Pres | Flux | Time | Place |
|---|---|---|---|---|
| NozzUp | 10.0 | 0.0 | 1.00 | ****** |
| NozDown | 5.0 | 0.0 | 1.00 | ****** |
| L. Keep | 20.0 | 0.0 | 1.00 | ****** |
| L. EjcAdv | 40.0 | 0.0 | 1.00 | ****** |
| L. EjcRet | 10.0 | 0.0 | 1.00 | ****** |
| R. Keep | 0.0 | 0.0 | 1.00 | ****** |
| R. EjcAdv | 5.0 | 0.0 | 1.00 | ****** |
| R. EjcRet | 5.0 | 0.0 | 1.00 | ****** |
| L. EjectPlac | ****** mm |
| R. EjectPlac | ****** mm |
| AutoNozRet | Disable |
| EjectFunc | Disable |
| EjectMode | Times |
| Ejec. Times | 1 |
| EjecAdvDel | 1.00 S |
| EjecRetDel | 0.00 S |
PORCHESON Temp. Set
| TempCurve | Ejec | 1Seg | 2Seg | 3Seg |
|---|---|---|---|---|
| Meas (°C) | ***** % | <temp> | <temp> | <temp> |
| Set (°C) | ***** | 200.0 | 200.0 | 200.0 |
| Max (+) | *** | 75.0 | 75.0 | 75.0 |
| Min (-) | *** | 75.0 | 75.0 | 75.0 |
| Station | **** | Lower | Lower | Lower |
| Eje. Mode | O.ring | Scr. C. BT. T | 2.00 S | Galv | |
| KeepWarm | Disable | Insulation valu | *** °C |
NOTES/HISTORY
- 2026-07-28 - Updated tables. The mold shot with just a little flash and ejected properly.
- 2026-07-09 - Created page to capture information